Small Copper Pillars and Discs for PCB Thermal Contact: Process, Plating and Packing
A recent request from a European electronics manufacturer is typical of this kind of part: high-conductivity copper cylinders of Ø2.0 mm (+0.10/0) by 1.20 ±0.02 mm, used as thermal contacts between a PCB and an aluminium radiator, with 500 samples first and then a ramp through 10,000 and 500,000 to one million pieces within about half a year. The buyer did not know which finishes a stamping supplier can offer, and asked about tin, silver, gold and bare copper. This guide sets out the choices that decide the price and the quality of these small pillars.
1. Choose the copper grade by conductivity, not by price alone
| Grade (EN / UNS) | Thermal conductivity, approx. | When to use it |
|---|---|---|
| Cu-ETP, CW004A / C11000 | about 390 W/m·K | Standard choice for soldered thermal and electrical contacts |
| Cu-OF, CW008A / C10200 | about 390 W/m·K | When parts will be brazed or heated in hydrogen, or the drawing asks for oxygen-free copper |
| Cu-DHP, CW024A / C12200 | about 340 W/m·K | Common in tube and plumbing; lower conductivity, so not a like-for-like substitute for a heat path |
The values are typical room-temperature figures from public material data; check the supplier's certificate for the actual grade. If your requirement is stated as a conductivity range (for example 330–400 W/m·K), ETP or OF copper meets it and DHP is at the bottom edge.
2. How the part is made changes with quantity
| Quantity | Usual route | What it means for you |
|---|---|---|
| Hundreds (samples) | Cut-off from drawn rod or turning on a sliding-head lathe | No tooling charge; clean cylindrical side; faces cut or faced; higher price per piece |
| Around 10,000 | Turning, or a simple blanking die if the faces allow it | Small tooling cost if a die is used; check that sample and production routes give the same edge |
| Hundreds of thousands to millions | Blanking from 1.2 mm strip (with shaving or fine blanking for a clean side), or cold heading from wire | Lowest piece price; tooling paid once; the edge has a rollover and a burr side that must be controlled |
A Ø2 mm punch in 1.2 mm copper is close to the limit where conventional blanking still gives a straight side, so a production quote should say whether the side is plain-blanked, shaved or fine-blanked. If sample parts are turned and production parts are blanked, the edge and the burr will not be the same; ask for a short pre-series from the production route before you approve the million-piece release.
3. Faces, flatness and burrs
With grease or a thermal pad in the joint, the faces do not need to be lapped, but they must sit flat on the solder pad and on the pad material. The real risk is a burr on one face that tilts the pillar during reflow. Put a maximum burr height and, if it matters, the burr side on the drawing, and say how parts may be deburred: vibratory finishing in media works for copper, but tumbling very small parts for too long rounds and peens the edges. Our guide to burr height and burr direction covers how to write this on a drawing.
4. Solderable finish: tin, silver, gold or bare copper
- Matte tin, about 3–5 µm, optional nickel 1–3 µm underneath: the usual choice for SMT reflow. Matte (pure) tin is preferred over bright tin because it is less prone to whiskers; the nickel underlayer acts as a barrier against copper–tin intermetallic growth, which helps shelf life.
- Silver: very solderable and conductive, but it tarnishes in air containing sulphur, so it needs sealed packing and a limited storage time.
- Gold over nickel: long shelf life and a stable surface, at a clearly higher cost; usually only worth it if the parts will be stored for a long time or used in a harsh environment.
- Bare copper: cheapest, but it oxidises; it must be cleaned of oil, packed in sealed or vacuum bags and soldered within a short window.
Small parts like these are barrel plated, so thickness varies from part to part. Specify a minimum thickness rather than a nominal one, and the measuring method (XRF is usual), so that quotations are comparable.
5. Packing for pick-and-place
If the pillars go through SMT reflow with pick-and-place, they need embossed carrier tape and reels to EIA-481. Agree the pocket size, the pitch, the tape width and the reel diameter before samples, because the pocket has to be designed for the part and the samples should be packed the same way as production. Loose parts in bags are fine only for manual or selective soldering.
6. What to send in the RFQ
- Drawing with diameter, height, tolerances, maximum burr height and face requirements.
- Copper grade (for example Cu-ETP / CW004A / C11000) or the conductivity range you need.
- Finish and minimum thickness, for example matte Sn 4 µm min over Ni 2 µm, or bare and clean.
- Soldering method and packing: SMT reflow on tape and reel, or loose parts.
- Quantity steps and dates, for example samples, first production lot and yearly volume.
- Documents (COC, mill certificate, EN 10204 3.1) and delivery terms (FOB China or DAP to your site).
How we quote these parts
We quote small copper parts for each quantity step and name the process behind each price, so you can see where tooling is needed and where it is not. Parts are produced through our production network across Guangdong, Zhejiang, Jiangsu, Shandong and Fujian, including partner plating and packing shops. Our tolerance on critical stamped dimensions is ±0.01 mm. We can quote FOB China and delivered terms, and we reply to drawings within 24 hours. See also our copper and brass stamping page.
Frequently asked questions
What finish should I specify on a small copper pillar that is reflow-soldered to a PCB?
Matte (pure) tin of roughly 3–5 µm is the common choice, optionally over a 1–3 µm nickel underlayer. Tin solders well in SMT reflow, matte tin is preferred over bright tin to reduce whisker risk, and the nickel layer slows copper–tin intermetallic growth during storage and reflow. State a minimum thickness and the measuring method (usually XRF) on the drawing.
Is a 2 mm copper pillar stamped, turned or cold headed?
It depends on quantity. Sample lots of a few hundred pieces are usually cut from drawn rod or turned, because no tooling is needed. From tens of thousands upwards, blanking from 1.2 mm strip or cold heading from wire becomes cheaper per piece. Ask the supplier which route the price is based on, because the edge shape and burr differ between them.
Which copper grade gives the best thermal conductivity for a heat-spreading pillar?
Cu-ETP (CW004A / C11000) and oxygen-free Cu-OF (CW008A / C10200) both have a thermal conductivity of roughly 390 W/m·K at room temperature. Phosphorus-deoxidised Cu-DHP (CW024A / C12200) is noticeably lower, at roughly 340 W/m·K, so write the grade on the RFQ and do not accept 'copper' without a grade.
Can the pillars be delivered on tape and reel for pick-and-place?
Yes. Small loose parts can be packed in embossed carrier tape to EIA-481, with the pocket size, pitch, tape width and reel diameter agreed before the first lot. Packing adds a cost per piece and needs a pocket design, so ask for it in the first RFQ rather than after samples.
Is a certificate of compliance enough, or do I need EN 10204 3.1?
For many electronics buyers a certificate of compliance (COC) against the drawing is enough. If you need traceability to the copper heat, ask for a mill certificate of the rod or strip as well, or an EN 10204 3.1 certificate, and say so in the RFQ.
Send your drawing for a quote
Send the drawing with the copper grade, finish and thickness, packing (tape and reel or loose), quantity steps and delivery country. We reply with a quote and a DFM review within 24 hours.